HOW TO SIZE YOUR STACKED RINGS

1-img_3366Sizing a ring is pretty easy.  It just takes a little applied mathematics.  First, determine the inner diameter of the desired ring size. Then, take the inner diameter, add the thickness of your wire and multiply by pi…3.14.

Example:  To make a size 7 ring with 14 gauge wire (1.63mm thick) follow this calculation.

To 17.35  (inner diameter of size 7) add 1.63  (thickness of 14 gauge wire)  for a total of 18.98.  Multiply 18.98 by pi (3.14) for a grand total of 59.60mm  (total length of wire needed…see SPECIAL NOTE)

In this case, round the measurement up to 60mm.  When cutting your wire stock, make sure that it is straight along your measuring tool for an accurate cut.  Also, use a quality flush cutter. This prevents having to sand off a large amount of wire in order to solder two perfect wire ends together.

SPECIAL NOTE:  

Keep in mind that after soldering the wire ends together your metal will be soft.  Treat it with care so as not to mar the ring surface.  Also, it’s important to remember that wire will expand when hammered.  Therefore, please follow the guidelines below.  Depending on the manner of your hammer blows the ring could possibly become larger than intended. Use your ring mandrel to regularly check sizing.

  • Reduce your wire length by 1/4 size to allow for shaping your ring after soldering.
  • Reduce your wire length by 1/2 size to allow for stamping or embossing your ring after soldering.

Your may add interest to your ring by lightly hammering the outer surface using either end of a chasing hammer.  Or perhaps by using a metal stamping tool, such as a “period” or “starburst” to create a design.  Wire stock is sold in many forms as well.  Round, square, beaded and patterned wire, to name a few, will add an artistic dimension to your rings.

There are numerous educational websites to help the jewelry maker along his or her way.  I personally prefer to visit Rio Grande,  Beaducation and Contenti on the web for my jewelry making supplies and additional help in the way of videos and blogs. A wonderful YouTube channel features Mr. Soham Harrison who masterfully takes the jewelry making student to more involved levels.  Additionally, there are myriads of sites devoted to US and UK ring sizes, wire gauge sizes and ring calculators.

You just might be surprised at how satisfying and enjoyable calculating the exact ring measurements may be.  Not to mention having a new set of stack rings to wear!

TOOLS FOR THIS PROJECT:

  • 14 gauge sterling silver wire (copper wire can be used for practice if desired)
  • flush cutter
  • measuring ruler, caliper or sliding gauge in mm
  • #2 file
  • soldering equipment *
  • finishing and polishing equipment*

* To be covered in a subsequent lesson.

If you have any questions or comments regarding this article or jewelry making in general please be sure to leave them in the comment box below.  Thank you!

Take The Plunge…Silver Smithing Class

Have you ever wanted to take your current skills to the next “level”?  How much will it cost?  How much of my time will it take up?  In the end, will it be worth it?  The answer is a resounding  “YES”!  Here’s the scoop in my location, Cleveland, Ohio.

I found an amazing teacher through a web search.  She was skilled, knowledgeable and witty.  The witty part was especially fun!   I talked a good friend to take the class with me.  That arrangement worked out beautifully since we took an evening class!  The length of the class was three (3) hours, once a week for five (5) weeks.  The price of $150.00 was very reasonable.  Even though it was a beginner’s class, we were able to make a very substantial sterling silver ring with a stone cabochon setting.  The price for supplies was only $15.00!  All the tools we used belonged to the instructor and were left at the studio at the end of class.

I’m so glad I took the class!  I bumped up my jewelry making skills, made a new friend and found that IF I want to use the instructor’s tools (for a small fee) I can!  Also, the instructor would be available for further instruction.  By the way, she also offers an intermediate silversmithing class.

Please be sure to stop by her studio to see all that she offers.  You’ll be very glad you did!  If you have any questions about taking a silversmithing class I would be happy to share with you!   Have fun!  Here’s the link to an awesome experience:

SAS Design Studio:  http://www.sasdesignstudio.com/

 

 

Dremel “Heaven”

Well it’s here…my new Dremel tool!  This is a great little tool to help reduce the time it takes to complete a new piece of metal jewelry.  I really don’t mind the time involved.  However, it’s nice to become familiar with tools that other jewelry buffs have used and advocate.

One task used was to sand down the sharp edges on the blanks I cut with my disc cutter.  The Dremel worked well for this task.  However, hand sanding works just as well.  I have also used the Dremel to smooth out a rough imperfection on the top of a blank.  This was a total success!  Otherwise, I would have had to change the surface by some manner, such has skipping the alphabet stamping and just presenting a hammered surface.

Polishing is another time-consuming phase of working with metal.  I bought a couple of polishing accessories for this task.  One states that the polishing compound is already built into the fibers.  The other uses a polishing compound that you apply to the polishing accessory.  Both have their uses.  As it stands now, I prefer polishing my metal jewelry by hand.

These are just a few of the tasks the Dremel tool is capable of.  All-in-all, the Dremel tool is a handy-dandy tool to have in your jewelry work bench.  Hopefully, this little note will be of help to you as you consider whether or not to purchase a rotary tool.

Happy jewelry making!

Sam

 

Beginning a New Journey

Just another day in paradise…at my jewelry bench.

Today begins my aspirations to use sterling silver and gold-filled metals in my jewelry making.  I have been inspired by other metal artisans who have created some very pretty and interesting jewelry.

For the past year or so I have been using the base metals of copper and brass.  These metals are fairly inexpensive to work with, as well as interesting in their own rights.  I love working with copper!   The metal properties of copper are fascinating to learn about and the color is so rich and warm.  I have cut out discs, sawed, filed, sanded, textured, soldered, oxidized, tumbled and polished copper pendants and bracelets.  I have used brass to a lesser degree.  It is more difficult to oxidize, which is a good thing if you don’t like an oxidized look.  I don’t have the same affection for brass, but like most things it has it’s place.

So, there you have it.  Stay tuned…the learning curve is just beginning…